PLUMBER'S ESSENTIALS: WHAT YOU NEED FOR INSTALLING A BATHTUB

Plumber's Essentials: What You Need for Installing a Bathtub

Plumber's Essentials: What You Need for Installing a Bathtub

Blog Article

Browse Our Site

Were you in search of facts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


Tools You Need to Install a New Bathtub
Mounting a bath tub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough project. If the old bathtub is easily obtainable, the task can move speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and embeded in the new one. Make certain you have actually qualified yourself for the work as well as fit trying it. Instead of hiring a professional to take control of a halfway-completed job, it is better to consider employing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This article will certainly help you mount a new tub in your bathroom if you have actually already bought a new tub and also don't need to alter the setup of your previous supply of water pipelines.
Your devices and product checklist ought to make up the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome due to the limited accessibility that is usually the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
    Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in place between the tap and the sink. Safeguard the faucet in position with the producer provided backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

    Installing the Tub


    Using the two wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
    The next objective is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bath tub until the level reviews level.
    To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
    Activate the water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the bathtub as well as likewise check the overflow outlet and also the typical electrical outlet for leakages.
    Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bath tub must wait until the bathtub has actually been made use of at the very least once as this will settle it right into its last setting.

    Planning for the Setup


    Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
    Fit the flexible tap adapters to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last placement.

    Tiling Around the Bathtub


    In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to pass through the wall between the bath and also the tiling, causing issues with wetness and also feasible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into account this motion prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly offered on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I am just very fascinated by Tools You Need to Install a New Bathtub and I really hope you enjoyed reading our piece. Do you know about someone else who is excited about the niche? Please feel free to promote it. I praise you for your time. Visit us again soon.


    Reliable every time!

    Report this page